Mixx 0 Report post Posted July 13, 2017 MyGica HD Cap X, doesn't record Hi everyone, I was fully testing this device today, turns up that it doesn't support all 1080p variants, i was able to rec from one 1080p source (pc), but couldn't rec from another device (bluray device output) with the same res,.. so, it counts the colorspace, framerate, etc. to rec properly? or is there a list of all compatible modes? the manual was pretty minimalistic about that. The signal that is not working is this one: 24 Bit/Pixel, RGB, 1920x1080P60 according the manual. Full spec of format according manual: HDMI 1.X single link type A, 24bit/pixel, max 165Mhz, max res 1920*1200 with reduced blanking, no HDCP-support, no audio support, for HDMI 1.x monitors. Testing I've tryed this set of resolutions, the only parameter i can touch. 1080p (1980*1080) progressive. Didn't work 1080i (1980*1080) interlaced. Malfunction : Droped bad signal, screen cut at half- WUXGA (1920*1200) Didn't work 1280*1024: Worked great recording at 1080p, at 720p with wrong aspect ratio but still recorded. Feeding the device from the input and connecting the monitor from the output, I can actually see the image in all cases and is a good signal, so is somehow compatible, but not fully since doesn't rec of course. Waiting for comments. Thanks in advance. Share this post Link to post Share on other sites
Mixx 0 Report post Posted July 13, 2017 little mistake : should say on resolutions: Testing I've tryed this set of resolutions, the only parameter i can touch. 1080p >>>> (1920*1080) <<<<<< progressive. Didn't work 1080i >>>>>(1920*1080)<<<<<< interlaced. Malfunction : Droped bad signal, screen cut at half- WUXGA (1920*1200) Didn't work Share this post Link to post Share on other sites
zxl 12 Report post Posted July 28, 2017 Please try to update to the latest firmware and check it again: https://mega.nz/#!z91yTL5R!6Ff-qjMn4ojctwTLQGv6gPJw0TqxnbiVq3ZrQ3-heJo Share this post Link to post Share on other sites
Fra 0 Report post Posted March 14, 2018 Hello. I'm experiencing a different problem at the moment. Following what was said by the user before me, I did not find a way to record, so via the link, I upgraded. But once the red LED flashes for a few seconds, when it stops and restarts the mygica, it receives no signal. Only the power light stays on, but nothing else. What should I do in this case? Do I remove the power and turn it back on? Can this cause problems? I await your reply. Thank you Share this post Link to post Share on other sites
zxl 12 Report post Posted May 14, 2018 On 3/14/2018 at 10:25 PM, Fra said: Hello. I'm experiencing a different problem at the moment. Following what was said by the user before me, I did not find a way to record, so via the link, I upgraded. But once the red LED flashes for a few seconds, when it stops and restarts the mygica, it receives no signal. Only the power light stays on, but nothing else. What should I do in this case? Do I remove the power and turn it back on? Can this cause problems? I await your reply. Thank you What is your video source? How do you connect the HD Cap X with the video source? What is your receiving device? Could you please send us a screenshot by email or here? My email address: angela.xu@geniatech.com Share this post Link to post Share on other sites
Mixx 0 Report post Posted June 11, 2018 On 7/28/2017 at 4:22 AM, zxl said: Please try to update to the latest firmware and check it again: https://mega.nz/#!z91yTL5R!6Ff-qjMn4ojctwTLQGv6gPJw0TqxnbiVq3ZrQ3-heJo Hi ZXL, i downloaded the file provided but the results were the same. 1080p 60hz resolution not recognized 1080i 60hz screen crop in half 1280*1024: works great. Dou you think that it doesn't take 60hz input? maybe only 30hz? I can't configure this on my device to doowngrade the refresh rate, sadly for me. Any thoughts? Thanks in advance Mixx Share this post Link to post Share on other sites
zxl 12 Report post Posted June 13, 2018 On 6/11/2018 at 11:27 PM, Mixx said: Hi ZXL, i downloaded the file provided but the results were the same. 1080p 60hz resolution not recognized 1080i 60hz screen crop in half 1280*1024: works great. Dou you think that it doesn't take 60hz input? maybe only 30hz? I can't configure this on my device to doowngrade the refresh rate, sadly for me. Any thoughts? Thanks in advance Mixx With thehe new capture card, it works great. What doesn't work good is the mic connection. Share this post Link to post Share on other sites